0397155 JOHNSON THROTTLE CAM & INSERT ASSY.


0397155 THROTTLE CAM & INSERT ASSY. JOHNSON J3RCCM, J3RCUA, J4RCCS, J4RCEC, J4RCUD, J4RESR THROTTLE
0397155 THROTTLE CAM & INSERT ASSY. JOHNSON
Rating:
73

Buy THROTTLE CAM & INSERT ASSY. 0397155 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$209.87
 

16-02-2021

-: -
K&M 039-7155 Vinyl IH 806 Large Back, Black and White Vinyl
Durable fabric or vinyl covering || Steel core || Strong wear resistance || Strong wear resistance
Number on catalog scheme: 15
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J3RCCM 1988
J3RCUA 1987
J4RCCS, J4RLCCS 1988
J4RCEC, J4RLCEC 1989
J4RCUD, J4RLCUD 1987
J4RESR, J4RLESR 1990

Information:


Table 1
Parameter    Value    
Camshaft gear bolt torque     25 1 N m (18 1 lb ft) plus 45 degrees    
Rocker arm bolt torque    
100 10 N m (75 7 lb ft)    
Timing wheel bolt torque    
23 2 N m (17 1 lb ft)    Introduction
Use this procedure to check and/or adjust the camshaft and flywheel timing.Required Tools
Table 2
Required Tools for Camshaft Timing    
Qty     Part Number    
1     456-7990 Timing Pin    
1     456-7994 Engine Turning Tool    
Table 3
Required Tools for Flywheel Timing    
Qty     Part Number    
1     456-7990 Timing Pin    
1     456-7994 Engine Turning Tool    
    456-7997 Camshaft Timing Pin    Camshaft Timing Procedure
Reference.
Find the top center position for the number one piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g03710842
(1) 456-7990 Timing Pin
Install timing pin (1) into the flywheel.
Remove the camshaft gear cover.
Remove the camshaft speed timing sensor and camshaft timing wheel.
Remove the valve mechanism cover and loosen all of the rocker arm bolts.
Remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft Gear Remove and Install".
Illustration 2 g03836797
Typical example of the camshaft gear removed. Some parts have been removed for illustrative purposes. (2) Index hole
Illustration 3 g03836805
(2) Index hole (3) Camshaft sealing plate
Check the orientation of index hole (2) as shown above. If the index hole is in the proper orientation, proceed to Step 9.
If the index hole is not in proper orientation, rotate the camshaft in order to orientate the index hole as shown in Illustrations 2 and 3.
Illustration 4 g03710937
(4) Camshaft gear (5) Bolts
Install the camshaft, tighten bolts (5) to 25 1 N m (18 1 lb ft) and turn the bolts an additional 45 degrees.
Tighten all of the rocker arm bolts to 100 10 N m (75 7 lb ft).
Illustration 5 g03710965
Install a dial indicator on cylinder 3 exhaust rocker arm. Preload the dial indicator a minimum of 7 mm (0.28 inch).
Rotate the engine in a clockwise rotation until the dial indicator gauge reaches the minimum value possible.Note: Ensure that the rocker arm remains in contact with the camshaft during the measurement.
Zero the dial indicator.
Rotate the engine in normal counter clockwise rotation until the dial indicator measures 4.70 0.05 mm (0.19 0.002 inch).
Illustration 6 g03711096
(A) Double notch
Verify double notch (A) is visible from the inspection hole on the upper right-hand side of the flywheel housing and timing pin (1) can be inserted into the flywheel.If the timing pin cannot be installed and/or double notch (A) is not visible, the camshaft timing must be adjusted. Proceed to Step 16.If the camshaft is in time, proceed to Step 21.
Illustration 7 g03710937
(4) Camshaft gear (5) Bolts
Loosen bolts (5) , rotate the engine using the turning tool in order to install the timing pin and align the double notches with the inspection hole on the upper right of the flywheel housing. Refer to Illustrations 1 and 9.
Tighten bolts (5) to 25 1 N m (18 1 lb ft) and turn the bolts an additional 45 degrees.
Repeat Steps 12 through 17 un


Parts throttle JOHNSON:

0396925
 
0396925 THROTTLE CABLE ASSY.
J3RCCM, J3RCUA, J4RCCS, J4RCEC, J4RCUD, J4RESR
Back to top