0319890 JOHNSON THRUST BUSHING,Prop


0319890 THRUST BUSHING,Prop JOHNSON 25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, J20CRCCA, J20CRCDC, J20CRCEM, J20CRCOS, J20CRCUR, J20ECEM, J25ECCM, J25ECDR, J25ECEB, J25ECOC, J25ECUA, J25RCEM, J25RCSA, J25TECEM, J30ECCE, J30ECDM, J30ECED, J30ECOA, J30ECRR, J30ECUB, J30RCED, THRUST
0319890 THRUST BUSHING,Prop JOHNSON
Rating:
23

Buy THRUST BUSHING,Prop 0319890 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$36.87
 

10-03-2024
5.6[2.52] pounds
US: HARVARD MARINE
New Johnson Evinrude OMC Thrust Bushing 319890 1976-1989 20 25 30 35 HP
Johnson Evinrude OMC Sold Each || Sold Each || Please verify your own fitment
$44.99

26-08-2024
2.0[0.90] pounds
US: SEI Marine Products
SEI Marine Products-Compatible with Evinrude Johnson Thrust Bushing 0319890 Outboard Lower Units
SEI Marine Products This thrust bushing replaces OE#: 0319890 and fits Evinrude/ Johnson outboard lower units.
Number on catalog scheme: 59
 

BRP JOHNSON entire parts catalog list:

25E77S, 25EL77H, 25EL77S, 25R77H, 25R77S, 25RL77H, 25RL77S 1977
25E78C, 25EL78C, 25R78C, 25RL78C 1978
25E79R, 25EL79R, 25R79R, 25RL79R 1979
35E76G, 35E76S, 35EL76G, 35EL76S, 35R76G, 35R76S, 35RL76G, 35RL76S 1976
35E77C, 35E77H, 35EL77C, 35EL77H, 35R77C, 35R77H, 35RL77C, 35RL77H 1977
35E78R, 35EL78R, 35R78R, 35RL78R 1978
35E79A, 35EL79A, 35R79A, 35RL79A 1979
J20CRCCA, J20CRLCCA, J20ECCA, J20ELCCA 1988
J20CRCDC, J20CRLCDC, J20ECDC, J20ELCDC, J20TECDC 1986
J20CRCEM, J20CRLCEM, TJ20CRCEM, TJ20CRLCEM, TJ20CRLESF 1989
J20CRCOS, J20CRLCOS, J20ECOS, J20ELCOS 1985
J20CRCUR, J20CRLCUR, J20ECUR, J20ELCUR 1987
J20ECEM, J20ELCEM 1989
J25ECCM, J25ELCCM, J25RCCA, J25RLCCA, J25TECCA, J25TELCCA 1988
J25ECDR, J25ELCDR, J25RCDC, J25RDC, J25RLCDC, J25TECDC, J25TELCDC 1986
J25ECEB, J25ELCEB, TJ25ELCEB, TJ25ELESF 1989
J25ECOC, J25ELCOC, J25RCOS, J25RLCOS, J25TECOS, J25TELCOS 1985
J25ECUA, J25ELCUA, J25RCUR, J25RLCUR, J25TECUR, J25TELCUR 1987
J25RCEM, J25RLCEM 1989
J25RCSA, J25RLCSA, J25TECSA, J25TELCSA 1980
J25TECEM, J25TELCEM 1989
J30ECCE, J30ELCCE, J30RCCE, J30RLCCE, J30TECCE, J30TELCCE 1988
J30ECDM, J30ELCDM, J30RCDM, J30RLCDM, J30TECDM, J30TELCDM 1986
J30ECED, J30ELCED, TJ30ELCED, TJ30ELESF 1989
J30ECOA, J30ELCOA, J30RCOA, J30RLCOA, J30TECOA, J30TELCOA 1985
J30ECRR, J30ELCRR 1984
J30ECUB, J30ELCUB, J30RCUB, J30RLCUB, J30TECUB, J30TELCUB 1987
J30RCED, J30RLCED 1989
J30TECED, J30TELCED 1989
J35ECIG, J35ELCIG, J35RCIG, J35RLCIG 1981
J35ECND, J35ELCND, J35RCND, J35RLCND, J35TELCNB 1982
J35ECRR, J35ELCRR, J35RCRR, J35RLCRR, J35TELCRR 1984
J35ECSM, J35ELCSM, J35RCSM, J35RLCSM 1980
J35ECTS, J35ELCTS, J35RCTS, J35RLCTS, J35TELCTS 1983
J35RCCE, J35RLCCE 1988
J35RCDM, J35RLCDM 1986
J35RCED, J35RLCED 1989
J35RCUB, J35RLCUB 1987

Information:


Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Plug or cap all open ports with new plugs or caps.
If necessary, remove the diesel particulate mounting bracket. Refer to Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
Illustration 1 g02912798
Illustration 2 g02898616
Illustration 3 g02898617
If necessary, remove bolts (1) and heat shield (2) from exhaust gas recirculation (EGR) valve (4).
Slide the locking tab into the unlocked position and disconnect harness assembly (3) from EGR valve (4).
Loosen clamp (6) and position the clamp away from EGR valve (4).
Disconnect hose assembly (5) from EGR valve (4).
Remove bolt (18) from the bracket for tube assembly (19).
Remove bolt (20) and tube assembly (19) from EGR valve (4).
Remove O-ring seal (21) (not shown).
If necessary, slide hose clamp (17) along hose (16). Disconnect tube (19) from hose (16).
Apply releasing fluid prior to and during the removal of bolts (12) and bolts (14).
Remove bolts (12) and remove bolts (14). Remove flexible tube assembly (13) from the exhaust manifold.
Remove bolts (11) from EGR valve (4). Note: Note the position of different length bolts.
Remove from EGR valve (4) from the induction manifold.
If necessary, remove bolt (9) and remove tube assembly (7) from EGR valve (4). Remove O-ring seal (8) (not shown). Installation Procedure
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 4 g02898617
Illustration 5 g02898616
If necessary, install new O-ring seal (8) (not shown) to EGR valve (4). Install tube assembly (7) to EGR valve (4).
Install new clamp (6) to EGR valve (4).
Position a new clamp (6) onto EGR valve (4).
Install bolts (11) to EGR valve (4) finger tight.
Position clamp (6). Tighten the clamp to a torque of 10 N m (89 lb in).
Tighten bolts (11) to a torque of 25 N m (221 lb in). Note: Ensure that the bolts are installed into the correct position.
If necessary, install tube (19) to hose (16). Slide hose clamp (17) into position and tighten securely.
Install new O-ring seals (21) (not shown) to tube assembly (19).
Install tube assembly (19) to EGR valve (4).
Install bolt (18) and bolt (20) finger tight. Tighten the bolt
Tighten bolt (20) to a torque of 10 N m (89 lb in).
Tighten bolt (18) to a torque of 25 N m (221 lb in).
Position new gasket (15) onto flexible tube assembly (13).
Position flexible tube assembly (13) onto the exhaust manifold. Install bolts (14) finger tight. Note: Ensure that the flexible tube assembly can move freely.
Position gasket (10) (not shown) between flexible tube assembly (13) and EGR valve (4). Install bolts (12) finger tight. Note: Ensure that the flexible tube assembly can move freely and the gasket is correctly positioned.
Tighten bolts (12) to a torque of 25 N m (221 lb in).
Tighten bolts (14) to a torque of 25 N m (221 lb in).
Install hose assembly (5) onto pipe (7). Position hose clamp and ti


Parts thrust JOHNSON:

0319667
 
0319667 THRUST WASHER
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, D25RWA, HJ25FPO, HJ25FPV, J25ECIB, J25ECNE, J25ECRS, J25ECTD, J25RCSA, J25RSA, J25RSLS, J25RWCDC, J25RWCOS, J25RWCRD, J25RWCUR, J25RWEIM, J25RWENB, J25RWEOS, J25RWERD, J25RWESA, J25RWETE, J25RWK
0319684
 
0319684 THRUST WASHER
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS,
0319685
 
0319685 THRUST WASHER,Rear
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, J25RCSA, J35ECIG, J35ECND, J35ECSM, J35ECTS
0319686
 
0319686 THRUST WASHER,Front
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, J25RCSA, J35ECIG, J35ECND, J35ECSM, J35ECTS
0330441
 
0330441 THRUST WASHER, Bearing
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, BJ30BAECS, BJ30BAEDE
0397736
 
0397736 THRUST WASHER & SEAL
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM,
Back to top