12323A 1 Mercury BUNGY CORD ASSEMBLY


12323A 1 BUNGY CORD ASSEMBLY Mercury 1115473WD, 11354120D, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1150413SD, 1150413VD, 1150413WD, 1150453JD, 1175413MD, 1200413GD, 1200453EY, 1200453HY, 1200473UD, 1200473VD, 1200473WD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73H BUNGY
12323A 1 BUNGY CORD ASSEMBLY Mercury
Rating:
23

Buy BUNGY CORD ASSEMBLY 12323A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Mercury entire parts catalog list:

1115473WD 2000
11354120D 1990,1991
1135412MD 1992,1993,1994,1995
1135412SD 1996,1997,1998
1135412VD 1999
1135412WD 2000,2001,2002,2003,2004,2005
1135473UD 1998
1135473VD 1999
1150413SD 1996,1997,1998
1150413VD 1999
1150413WD 2000,2001
1150453JD 1990
1175413MD 1992,1993,1994,1995
1200413GD 1989,1990
1200453EY 2006
1200453HY 2006
1200473UD 1998
1200473VD 1999
1200473WD 2000
1200D73AD 2003
1200D73CD 2004,2005,2006
1200D73ET 2006,2007,2008
1200D73HT 2006
1200E73EY 2006,2007
1200E73HY 2006
1225412VD 1999,2000,2001
1225413EY 2007
1225413RD 1995,1996,1997,1998
1225423EY 2007
1225424EY 2007
1225E73AD 2003,2004,2005,2006
1250413UE 1998,1999,2000,2001
1250424EY 2007,2009
1250433EY 2007
1250434EY 2007
1256413WD 2000,2001,2002

Information:


Illustration 1 g00365332
Instructions for 1U-6431 Piston Ring Groove Gauge Piston Rings C30
The top two rings are the KEYSTONE rings, which are tapered. A special 224-9760 Piston Ring Groove Gauge is available to check the top two ring grooves in the piston. Refer to Guideline For Reusable Parts, "Pistons And Cylinder Liners".Connecting Rods And Pistons
3412E
Use the 7M-3978 Ring Expander to remove piston rings or install piston rings.Use the 5P-3526 Piston Ring Compressor to install pistons into the cylinder block.Tighten the connecting rod nuts in the step sequence that follows:
Apply 4C-5593 Anti-Seize Compound to the threads of the bolts and the contact surfaces of the bolt head.
Tighten all nuts to the following torque.Torque for nuts ... 82 8 N m (60 6 lb ft)
Put an alignment mark on each cap and bolt.
Tighten the nuts from the mark to the following value.Angle from the mark. ... 120 5 degrees C30
Use the 7B-7974 Piston Ring Expander to remove piston rings or install piston rings.Use the 200-3914 Piston Ring Compressor to install pistons into the cylinder block.
Illustration 2 g00875778
Connecting rod boltsUse the following procedure to tighten the connecting rod bolts:
Put engine oil on the bolt threads and the contact surfaces before assembly.
Tighten the bolts in the following order.Torque for bolts (1) and (3) ... 70 4 N m (52 3 lb ft)Torque for bolts (2) and (4) ... 70 4 N m (52 3 lb ft)Additionally tighten each bolt. (2) and (4) ... 60 5 degreesTorque for bolts (1) and (3) ... 70 4 N m (52 3 lb ft)Additionally tighten each bolt. (1) and (3) ... 60 5 degreesConnecting Rod Bearings
The connecting rod bearings fit tightly in the bore in the rod. If the bearing joints are fretted, check the bore size. This can be an indication of wear because of a loose fit.Connecting rod bearings are available with 0.63 mm (0.025 inch) and 1.27 mm (0.050 inch) smaller inside diameter than the original size bearing. These bearings are for crankshafts that have been ground.Main Bearings
Main bearings are available with a larger outside diameter than the original size bearings. These bearings are used for the cylinder blocks with the main bearing bore that is made larger than the bores' original size. The size that is available has a 0.63 mm (0.025 inch) outside diameter that is larger than the original size bearings. These bearings are available with a standard inside diameter. Also, these bearings are available with a 0.63 mm (0.025 inch) inside diameter for crankshafts that have been ground.Main bearings are available with a smaller inside diameter than the original size bearings. These bearings are used for the cylinder blocks with a crankshaft that is made smaller than the crankshaft's original size. The size that is available has a 0.63 mm (0.025) and 1.27 mm (0.050 inch) inside diameter that is smaller than the original size bearings. These main bearings are for crankshafts that have been ground.Cylinder Block
If the main bearing caps are installed without bearings, the bore in the block for the main bearings can be checked. Tighten the nuts that hold the caps to the torque that is shown in the Specifications, "Cylinder Block". Alignment error in the bores must not be more than 0.08 mm (.003 inch). Refer to Special Instruction, SMHS7606 for instructions on the use of 1P-4000 Line Boring Tool Group .The 1P-3537 Dial Bore Gauge Group can be used to check the size of the bores. The Special Instruction, GMGO0981 is with the group.
Illustration 3 g00294303
1P-3537 Dial Bore Gauge Group Projection Of Cylinder Liners
Note: This procedure alleviates the need for the "H" bar to hold down liners during liner projection measurements.
Table 1
Tools Needed    
Part Number     Part Name     Quantity    
8T-0455     Liner Projection Tool Group     1    
Illustration 4 g00294304
Liner projection components (1) Bolt. (2) Washer. (3) Washer. (4) Spacer plate. (5) Block. (6) Cylinder liner.
Illustration 5 g00533892
Table 2
Components that are needed    
Item     Part Number     Description     Quantity For One Cylinder     Quantity For Six Cylinders    
1     7H-3598     Bolt   &nb


Back to top