859223 SENSOR, Speed/Temperature Mercury
1115473WD, 1200473WD
SENSOR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$112.48
13-04-2021
-: -
Mercury Marine New Filter-Oil Part Number # 805809 New Sensor-Speed/Temp Part Number # 859223
$87.95
21-03-2024
0.5[0.23] pounds
US: Boating Accessories
Mercury / Quicksilver Sensor Speed/Temp
MERCURY Factory New.
MERCURY Factory New.
Mercury entire parts catalog list:
Information:
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not drain the engine lubricating oil when the engine is cold. As the engine lubricating oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed with draining cold oil. Drain the oil pan with the engine stopped. Drain the oil pan with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will cause the waste particles to be recirculated through the engine lubrication system with the new oil.Drain the Engine Lubricating Oil
Note: Ensure that the vessel that will be used is large enough to collect the waste oil.After the engine has been run at the normal operating temperature, stop the engine. Use one of the following methods to drain the engine oil pan:
Illustration 1 g03350504
Typical example
Remove the drain plug (1) in order to allow the oil to drain.
If the engine as an oil drain valve (3) installed, install a suitable flexible hose onto the valve (4). Turn the handle (2) counter clockwise and allow the oil to drain.
When the oil has drained, turn the handle clockwise and tighten securely. Remove the flexible hose.
Illustration 2 g03350650
Typical example
Remove O ring seal (5) and install new O ring seal.
Install drain plug and tighten drain plug to a torque of 34 N m (25 lb ft). Replace the Oil filter
Caterpillar oil filters are manufactured to Caterpillar specifications. Use of an oil filter that is not recommended by Caterpillar could result in severe damage to the engine bearings, crankshaft, as a result of the larger waste particles from unfiltered oil entering the engine lubricating system. Only use oil filters recommended by Caterpillar.
Remove the oil filter (3) with a 1U-8760 Chain Wrench.
Illustration 3 g01999595
Element with debris
Cut the oil filter open with a 175-7546 Oil Filter Cutter . Break apart the pleats and inspect the oil filter for metal debris. An excessive amount of metal debris in the oil filter may indicate early wear or a pending failure. Use a magnet to differentiate between the ferrous metals and the nonferrous metals that are found in the oil filter element. Ferrous metals may indicate wear on the steel and cast iron parts of the engine.Nonferrous metals may indicate wear on the aluminum parts, brass parts, or bronze parts of the engine. Parts that may be affected include the following items: main bearings, rod bearings, turbocharger bearings and cylinder heads.Due to normal wear and friction, it is not uncommon to find small amounts of debris in the oil filter. Consult your Cat dealer in order to arrange for a further analysis if an excessive amount of debris is found in the oil filter.
Illustration 4 g03351031
Typical example
Clean the sealing surface of the oil filter base (1).
Apply clean engine oil to the O ring seal (2) on the new oil filter.
Install the engine oil filter. Spin on the new oil filter until the O ring seal contacts the oil filter base. Rotate the oil filter ¾ of a full turn. Fill the Oil Pan
Remove the oil filler cap. Refer to this Operation and Maintenance Manual, "Fluid Recommendations" for more information on suitable oils. Fill the oil pan with the correct amount of new engine lubricating oil. Refer to this Operation and Maintenance Manual, "Refill Capacities" for more information on refill capacities.
If equipped with an auxiliary oil filter system or a remote filter system, follow the OEM or the filter manufactures recommendations. Under filling or over filling the crankcase with oil can cause engine damage.
Start the engine and run the engine at "LOW IDLE" for 2 minutes. Perform this procedure in order to ensure that the lubrication system has oil and that the oil filters are filled. Inspect the oil filter for oil leaks.
Stop the engine and allow the oil to drain back to the oil pan for a minimum of 10 minutes.
Illustration 5 g02173847
"L" Low
"H" High
Remove the engine oil level gauge in order to check the oil level. Maintain the oil level between the "L" and "H" marks on the engine oil level gauge. Do not fill the crankcase above the "H" mark.
Parts sensor Mercury:
13536A 2
13536A12
13536A12 SENSOR ASSEMBLY, Temperature
1115473WD, 1135473UD, 1135473VD, 1135473YD, 1200473UD, 1200473VD, 1200473WD, 1200473YD, 1F25201UD, 1F25203VD
13536A14
13536A14 SENSOR ASSEMBLY, Temperature (Starboard)
111047JHD, 1115473WD, 1135473UD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1150413WD, 1175P73HY, 1200473UD, 1200473VD, 1200473YD, 1200D73AD, 1200D73CD, 1200D73ET, 1200D73HT, 1200E73EY, 1200E73HY, 1225412VD, 1225E73AD, 1225P73DD, 1225P73ED, 1225P73H
858535
858535 SENSOR ASSEMBLY, Temperature
1115473WD, 1135473YD, 1150413ZD, 1200473WD, 1200473YD, 1200D73AD, 1225413ZD, 1A30302ZB, 1A41412ZB, 1B25203ZB, 1F25203VD, 1F30203VD, 1F40452YB, 1F41452YD, 1F51452YB
854445
854445 SENSOR, MAP
1075D73FY, 1075D73HY, 1090D73CD, 111047JHD, 1115473WD, 1115P73HY, 1115P73HY, 1125D73HY, 1135473YD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423HG, 1150423HY, 1150424FY, 1150424H
859604A 1
859596
859210T