09160-08119 Suzuki WASHER

INSTALL SPRING WASHERS AS SHOWN Any adjustment to the governor must be made only by a person approved by Caterpillar or by a Caterpillar Dealer.(1) Torque for nut ... 12 4 N m (9 3 lb. ft.)(2) 6N8793 Spring for the collar: Length under test force ... 19.05 mm (.750 in.)Test force ... 2.0 0.1 N (.45 .03 lb.)Free length after test ... 41.9 mm (1.65 in.)Outside diameter ... 9.40 mm (.370 in.)(3) Seat. Install a spring washer, flat washer and spring washer between seat (3) and spring (4) as shown.(4) 9L6448 Spring for governor: Color code ... one green stripe, one yellow stripePut force on spring of ... 18 N (4.00 lb.)Then add more force to make spring shorter by ... 22.86 mm (.900 in.)Total test force ... 63.3 1.4 N (16.60 .30 lb.)Free length after test ... 56.9 0.8 mm (2.24 .03 in.)Outside diameter ... 35.3 mm (1.39 in.)(5) 9M6303 Spring for low idle performance: Length under test force ... 4.57 mm (.180 in.)Test force ... 45 4 N (10 1 lb.)Free length after test ... 8.74 mm (.344 in.)Outside diameter ... 12.19 mm (.480 in.)(6) Diameter of the outer surface of the cylinder (new) ... 38.100 0.013 mm (1.5020 .0005 in.) Bore in the gear (new) ... 38.151 0.013 mm (1.5020 .0005 in.)(7) Install two dowels in governor drive gear to a dimension of ... 7.9 0.5 mm (.31 .02 in.)(8) Bore in the bearing (new) ... 22.263 0.038 mm (.8765 .0015 in.) Diameter of the gear, at the hub (new) ... 22.187 0.013 mm (.8735 .0005 in.)(9) Distance from the face of the plate to the bearing for the governor drive assembly ... 0.51 0.25 mm (.020 .010 in.)
CONTROL SHAFT BEARINGS
SHUTOFF SHAFT BEARINGS(10) Dowel installation: Angle A must be ... 54 10°Dimension B must be ... 7.9 0.5 mm (.31 .02 in.)(11) Install dowels to get a dimension of ... 5.6 0.5 mm (.22 .02 in.)(12) Bore in the governor control shaft bearings (new) ... 15.761 0.038 mm (.6205 .0015 in.) Diameter of the governor control shaft (new) ... 15.720 0.008 mm (.6189 .0003 in.)(13) Distance between the bearings for the governor control shaft ... 60.58 0.13 mm (2.385 .005 in.)(14) Distance from the face of the housing to the end of the bearing for the governor control shaft ... 43.38 0.15 mm (1.708 .006 in.)(15) Bore in the shutoff shaft bearing (new) ... 12.713 0.013 mm (.5005 .0005 in.) Diameter of the shutoff shaft (new) ... 12.637 0.013 mm (.4975 .0005 in.)(16) Torque for insulator ... 4.5 0.6 N m (40 5 lb. in.)(17) Needle bearing.(18) Distance from center of bolt hole to outside end of needle bearing (17) ... 92.86 0.25 mm (3.656 .010 in.)(19) Distance from end of needle bearing (17) to inside of sleeve bearing ... 98.68 0.25 mm (3.885 .010 in.)Install seals as shown.